Home Contact Enquiry Service Download

 

CB35E: 35-Unit Charging Bank for KH3E-Ex

 

PRODUCT CATEGORIES

 

Cordless Miner's Caplamps

IECEx Certified Petrochemical Helmet Lamps

Charging Banks

CB53E: For KH3E-Ex

CB35E: For KH3E-Ex

CB8E: For KH3E-Ex

CB53: For general models

CB35: For general models

CB8: For general models

Charging bank accessories

Lamp Accessories

Traditional Caplamp

Roobuck Caplamp Bracket

Hemet & Attachment

I.S. Helmet Beacons

I.S. LED Strap

LED Hi-Vis Safety Vest

LED Hi-Vis Lighting Vest

Cordless Sandblast Light

UG Mining Machine Headlight

ELV Tunnel Lighting System

LED Board Light

Steel Mesh Reinforced PE Pipe
   
CB35E Charging Bank is a wall mounting charging facility to charge 35 units ofd KH3E-Ex Helmet Lamps. It is compact, light weight, high capacity, low current, safe and easy to use. After starting the charging process, no further attention is

needed as the automatic over-load protection function in each charging unit will cut off that circuit when the battery is fully charged. CB35E has 5 rows and 7 charging units in each row.

Charging Unit
A charging unit supplies a 5.1VDC power to the caplamp. Two spring plate style electrical contacts not only guarantee the electrical contact to caplamp electrodes but also firmly hold the caplamp in place. A switch is located underneath the caplamp. With the caplamp inserted properly, the electrodes are connected and the switch is on. Each unit has a locking facility for padlocking the caplamp to the panel. A charging indicator indicates the charging state of this caplamp. There is a label groove on each side of the Charging unit, where you can stick a label to identify your position with your name, work number, group, photo or other information.

  

Power Distribution
The Charging Banks are powered from the 240VAC mains. A power supply generates a 12VDC and supplies it to all charging units. Thus, only extra low voltage is distributed in the cabinet thereby guaranteeing its safety. For CB53E, a Residual Current Breaker with Overload protection (RCBO) is located immediately after the power fuse to further safety of personnel.

1: Charging units
2: Power suppliers
3: Extra low power distribution
4: Mounting holes
Label Identification
There is a label groove in both left and right sides of each charging unit. You can label the charging position using position number, work number, miner¨s name, group name or other identification.
Stealing Prevention Facility



There is a padlock bracket under each charging unit. The lamp can be padlocked to this bracket through the lamp clip. It is suggested you padlock the caplamp whenever leaving it plugged in. It is recommended that mines use the Charging Bank as the only charging facility so that if a lamp is stolen it cannot be recharged. The individual chargers are intended for individual use only. For the CB53E, the charging units in upper 4 row place locks under the caplamps. The charging units in lower 5 rows are in opposite direction so to place the locks above the caplamps. Such an arrangement make the caplamps easy access no matter the caplamp is in a higher position or lower position.
Service
The circuits are accessible from the back panel, which can be opened by simply unscrewing the screws.

Charging Indication

The indicator starts from red for a fully uncharged caplamp, which is charged at a large relatively constant current. When the caplamp battery is nearly full, the indicator should flash alternatively in red and green and the charging current is gradually reduced with a constant voltage applied. When the indicator turns to steady green, no current is flowing and the battery is fully charged.
Installation
Four mounting holes are located in each of the four corners of the back panel. Four mounting kits are supplied. Two foot pads are also supplied in case the Charging bank will be standing on the ground.
Specifications
Charging Unit 35
Input 110VAC
Output to lamps 5.1VDC/500mA
Power consumption <175W
Dimension 87 x 11 x 56cm
Weight 16 Kg

Home | Contact | Feedback | Service | Download

Copyrights Roobuck Pty Ltd All Right Reserved